Power Flow Air Filter
Power Flow Air Filter

Power Flow Air Filter


Product Code: 600-202

Price: $49.99

In Stock: 23 
Quantity: Add to Basket

Smart PowerFlow High Performance Air Filter

"After all the testing we have found that the factory box is a sealed ram air box, which obtains air flow from only the outside (not hot air from the engine bay). Use of a high flow filter proved to out-perform the so-called cold air induction systems. The intake temp on the stock system, with a good high flow filter, was about 10 to 20 degrees cooler then the others thus giving a higher timing curve and optimum fuel mixture and increased Horsepower. This turned out to be an easy and cheap HP increase. Coupled with our .50 cent mod of the silencer part of the airbox removal again increased the HP and reduced 0-60 and 0-80 by over 1 second.
 

  • Performance High Air Flow with Excellent Filtration
  • Direct Fit
  • Designed to Increase Horsepower and Acceleration
  • Washable and Reusable
  • Will NOT Void Vehicle Warranty
  • Lasts up to 60,000 miles before cleaning is required depending on driving conditions 
  • Works with Original Equipment Manufacturer Vehicle Electronics
  • Easy High Performance Add-on
  • Easy Install
  • Environmentally Friendly

BPP’s FILTERS TESTS AND POSTS OUR FINDINGS TO THE STANDARDS MOST OTHER PERFORMANCE FILTER COMPANIES ARE SCARED TO USE: ISO 5011

The ISO (International Organization for Standardization) establishes and specifies uniform test procedures, conditions, equipment and a performance report to permit direct laboratory performance comparison of air filters and induction systems.

Testing to these high standards enables us to accurately measure our products against not only OEM [Original Equipment Manufacturer] equipment, but also to the competition, allowing us to establish the air filter performance benchmark, which we are determined to do.

ISO is a worldwide federation of national standards bodies. The work of preparing International Standards is normally carried out through ISO technical committees. The specific individual International Standard utilized by BPP’s and automotive manufacturers establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners, in this case, those used on internal combustion engines and compressors used in automotive and industrial applications.

Our filters test at airflows up to 1,000 cfm with its ISO 5011 Test Stand.

ISO 5011
Test Stand to compare airflow
of new intake kits to the
stock setup.

The performance characteristics of greatest interest are airflow restriction (differential pressure), dust collection efficiency and dust capacity. The ISO 5011 Standard is what our Filters adheres to as we seek innovations and improvements in our product line, and to test our products so they meet the highest standard possible. We feel this is the standard that all performance filter manufacturers should be using to develop their products.

The end result is simple: increased horsepower by reducing the restriction of the air filter and/or intake kit while still protecting the engine. Trust your performance needs to the only performance filter manufacturer who tests to these standards and post results.

Remember this is a cleanable filter, you can use our cleaning solution or use the K&N cleaning solution.

INSTALLATION INSTRUCTIONS

 

  1. Gain access to the engine compartment.
  2. Unclip the 3 tension clips to open the airbox lid and remove the stock filter.
  3. Install the new Breathless Performance Powerflow filter
  4. Push the 3 clips back in place.
  5. You are done!!!

 

 

Next Mod called the .50 cent fix: To remove the silencer box from the airbox.

This mod will give you a little more sound plus you will be able to increase the airflow to the engine, thus even more power!!

PowerFlow Air Filter  Part # 600-202        $49.99 

 

 

 

 

 

 

 

INSTALLATION INSTRUCTIONS

PowerFlow Aircleaner

     

 

INSTALLATION INSTRUCTIONS

 

  1. Gain access to the engine compartment.
  2. Unclip the 3 tension clips to open the airbox lid and remove the stock filter.
  3. Install the new Breathless Performance Powerflow filter
  4. Push the 3 clips back in place.
  5. You are done!!!

 

 

Remember this is a cleanable filter, you can use our cleaning solution or use the K&N cleaning solution.

 

Next Mod called the .50 cent fix: To remove the silencer box from the airbox.

This mod will give you a little more sound plus you will be able to increase the airflow to the engine, thus even more power!!

 

  1. First you should remove your stock airbox assembly and place on a table or work bench.
  2. You will need to cut the 2 plastic tubes to separate the silencer from the airbox. See pic.
  3. Now you need to cap off the holes with a quarter in each. It is the perfect fit and seal it around with silicone adhesive or JB weld. That is a .50 cent fix..
  4. Once dry reinstall your stock airbox with the new powerFlow filter.

 

 If you have any questions please call 954-925-7725

2070-F Tigertail Blvd

Building 2

Dania, Fl 33004

 

 

 

 
  • Corvette
  • Camaro
  • Firebird
  • Smart
  • Cadillac
  • V-Rod
  • Hummer
  • Mercedes Benz
 
Shopping Basket
Your basket is empty.
0Items in cart:
$0.00Total:
View Basket
 
Powered by CubeCart
Copyright Devellion Limited 2006. All rights reserved.