C6 Vortex Ram Induction System 2005-2007 LS2

C6 Vortex Ram Induction System 2005-2007 LS2


Product Code: 700-2005

Price: $538.00

In Stock: 25 
Quantity: Add to Basket

Vortex Rammer 2005-07 LS2

C6 Standard & Z06 CORVETTES

Up to 40+ HP!!!

with ram air at high speed

THE VORTEX RAMMER COLD AIR SYSTEM C6 VETTE

BREATHLESS PERFORMANCE PRODUCTS-  This vortex rammer kit  replaces the restrictive stock air box assembly.  Look closely at the filter and note that this is not the K&N filter that everyone sells.  This revolutionary air cleaner contains an internal vortex velocity stack.  It obtains cool, pressurized air from the radiator cavity through your modified shroud.  Air is forced through a sealed box, where in turn, it directly injects cold air into your intake.  (Lowering Manifold Air Temperature by almost 30 Degrees)

Remember, cold air means more power.  Our HP results have already shown up to 36HP and 38FT/LBS at the flywheel. Running at speed has give an additional up to 10 more Hp due to the air being forced in.. This is from the benefit of the pressurized air that is created at high speeds (which means there will be more h.p. at speeds over 35 MPH. 1/4 mile tests showed 3 MPH and .30 

C6 auto test one showed 26 flywheel HP

C6 stick test two showed 21 flywheel HP

BPP's powerduct is made out of a one piece unit not like our competitors 2 piece seamed units which have a tendency to crack along the seam.

The power duct replaces the stock air bridge between throttle body and MAF.   It increases the air flow to the motor by over thirty three percent.  

Can also be available with the C6 logo on top.....

 

The kits are available in CLEAR, BLACK and CARBON FIBER.

(Clear finish provides a visual access to your Filter and Radiator for service inspection.)

Note: Z06 model is available with factory MAF already installed.

2005 and up C6

Item 700-2005(L)  C6 Vortex Ram Induction system with Carbon Fiber Laminate box  

Price $ 569.99

Item 700-2005(C)  C6 Vortex Ram Induction system with Clear box

Price $ 538.99 

Item 700-2005(B)  C6 Vortex Ram Induction system with Black box

Price $ 538.99 

2008 C6

Item 700-2008(L)  C6 Vortex Ram Induction system with Carbon Fiber Laminate box  

Price $ 569.99

Item 700-2008(C)  C6 Vortex Ram Induction system with Clear box

Price $ 538.99 

Item 700-2008(B)  C6 Vortex Ram Induction system with Black box

Price $ 538.99 

 

2006 C6 Z06 and up

Note: Z06 model is available with factory MAF already installed.

Performance Computer Programming is Recommended

 

Item 700-2006(ZC)  C6 Z06 Vortex Ram Induction system with Clear box

Price $ 538.99 

Item 700-2006(ZCM)  C6 Z06 Vortex Ram Induction system with Clear box with MAF

Price $ 618.99

Item 700-2006(ZB)  C6 Z06 Vortex Ram Induction system with Black box

Price $ 538.99 

Item 700-2006(ZBM)  C6 Z06 Vortex Ram Induction system with Black box with MAF

Price $ 618.99

Item 700-2006(ZL)  C6 Z06 Vortex Ram Induction system with Laminate box

Price $ 569.99

Item 700-2006(ZLM)  C6 Z06 Vortex Ram Induction system with Laminate box with MAF

Price $ 644.99

 

 

Don't get fooled by the imitators !! Snorkels are for submarines not Corvettes !!!  Want to suck water or air !!

Larger Filter Opening Area then or Competitors Snorkel!!

Ours 135 sq in  there's about 40 sq in!!

Our Filtration Surface area measures over 300 sq in!!! That's like a 10"x 30" flat panel filter!!

 

Proven on the track and dyno to be the worlds most powerful ram induction system. Holds the record for Nevada high speed event 205 mph. Holds record for bolt on modified C6 at 10.30 @ 134 in 1/4 mile.

1st place winner at BG's BeachBend Raceway for the Air Box challenge 6 years in row !!!

 

Click Below for You Tube Video Collection From Breathless Performance, includes Install and Dyno Video

http://www.youtube.com/BPProducts

 

System comes with Vortex Ram Box, Powerduct and all Couplers

VORTEX RAMMER COLD AIR SYSTEM  2005 & Up

Standard C6 & Z06

Up to 40+ Horsepower !!!!

With the ram air effect at speed.

Test car had headers & Corsa exhaust. Test was done with and without the Vortex but keeping the Corsa and headers. Car produced 26RWHP 

Customer testimonial & Dyno sheet click here

C6 Vortex Install click here

 

Click Below for You Tube Video Collection From Breathless Performance, includes Install and Dyno Video

http://www.youtube.com/BPProducts

 

 

Below is a customers review:

CF Senior Member

Dave O's Avatar

Member Since: Feb 2006
Location: Antioch CA
Default Vortex CAI Install - My Impressions on Install and Performance (PICS, long)

I had been on the fence for a while trying to decide whether or not I wanted to install a CAI on my 06 A6. I wanted a true CAI, one that got its air from outside of the engine compartment. My only performance mod to date was a tune from Synergy Motorsports. I wondered if a CAI would help, and would I be able to feel a difference. I finally decided to just go ahead and do it. With that decision made, I now needed to decide on which one. I had narrowed my search to the Vararam, Callaway Honker and the Vortex Rammer.

There is a lot of good press on the performance of the Vararam, but a lot of negatives as well in regards to the fit and finish, and issues in regards to the seal of the filter. Personally, I also didn’t like the way that the Vararam left a gap between the unit itself and the shroud. This allows for a lot of debris/dust to enter the engine compartment. Since I have a lot of visual mods as well, this was an issue for me. I don’t race, but wanted a balance between performance and looks.

The Callaway seems to have good performance numbers as well, although maybe not quite as good as the Vararam. I also liked the fact that it looked close to stock once installed. The one issue with it is that you have to remove the shroud to install it. Depending on who you listen to, this task alone can range from anywhere between a real pain in the a** to not all that bad.

I finally decided on the Vortex Rammer. Its performance numbers seem to be in line if not better than that of the Vararam. There are some differences with the Vortex that are different than some of the other CAI units. You do not have to remove the shroud to install it, it seals to the shroud to prevent debris/dust from entering the engine compartment and you have a choice of three different air boxes - clear, black or carbon fiber (not real carbon fiber, just a carbon fiber look). You don‘t see as many threads on this unit, and I had to search quite a bit to find what info I could about it. If you go back a year or two, you’ll find a little more info on this unit as opposed to the past six months to a year. The price of the Vortex is around $75-$100 more than the Vararam and Honker, which may be why you don’t see as much talk about it on the forum. To me, the fit, finish and look are well worth the extra $$. We spent a lot on our Vettes, what‘s an extra $100 in the grand scheme of things.

The other thing I liked about the Vortex was the unique design and the attention to detail. The designers (Breathless Performance) try to reduce turbulence in the intake for better performance. The filter itself has a cone inside of it to help reduce this, as well as the elimination of the accordion boot downstream of the MAF. Once the unit is installed, it is pretty much a straight shot from the air bridge to the throttle body - no bends, change of direction or an accordion for the air to bump up around. I liked this attention to detain in the design.

The Vortex unit consists of four major parts. The air bridge, the filter box, the filter and a smooth coupler to replace your accordion coupler downstream of the MAF. The install was pretty straight forward. From start to finish it took me about 2-2 1/2 hours. One of the hardest parts was getting the old filter and couplings apart. The instructions were good and the template provided was of good quality. I only had to cut once, and did not have to do any trimming after the initial cut. What helped out a lot was a 5 minute video Breathless Performance has on their Website on installing the Vortex. It goes into a little more detail than the written instructions, and filled in any gaps nicely.

The performance of the Vortex did not disappoint. Yes, I can feel a difference. My car seems to pull much better now in the middle to upper RPM range. It feels very strong here. The day after the install, I took my car back to my tuner for any tweaks that he might have to make as a result of the Vortex. Instead of placing it on his dyno, he drove it around for about a half hour with his laptop and HP Tuners in tow to make some fine tune adjustments. Being that the Vortex is supposed to get more air at speed, driving it out on the street as opposed to putting it on the dyno makes sense. He did have to make some small moves to the fuel trim as he stated it definitely was getting a little more air. He also stated that for being relatively stock (other than my tune and Vortex), the car has a lot of get up and go.

If customer service is important to you, Ernie at Breathless Performance was great to work with. Even on off hours he answered my calls. I actually placed my order for the Vortex while Ernie was out at the track. Customer service at Breathless Performance was well above my expectations.

In conclusion, the Vortex is everything I wanted in a CAI. It performs great, looks great, and the install was relatively easy. I’m sure the performance difference between the Vararam, Honker and Vortex is relatively small, if none at all. But when adding up performance with ease of install, design, fit and finish the Vortex was a hands down winner for me. I hope this helps with anyone else trying to make this decision on a CAI.

Below are some pictures of the install. Enjoy


New smooth coupler downstream of MAF. You have to drill a small hole in it to insert the vent tube

 
  • Corvette
  • Camaro
  • Firebird
  • Smart
  • Cadillac
  • V-Rod
  • Hummer
  • Mercedes Benz
 
Shopping Basket
Your basket is empty.
0Items in cart:
$0.00Total:
View Basket
 
Powered by CubeCart
Copyright Devellion Limited 2006. All rights reserved.